These log messages refer to the CLI category.
2.5.1. [ID: 272] Failed adding CLI command data resource
- Log Categories
- CLI
- Log Message
- Failed adding CLI command data resource.
- Default Log Severity
- Critical
- Parameters
-
- Explanation
- A CLI command data resource could not be added.
- Gateway Action
- None
- Action Description
- None
- Proposed Action
- Verify that the system has sufficient memory available.
2.5.2. [ID: 443] All CLI commands could not be listed
- Log Categories
- CLI
- Log Message
- All CLI commands could not be listed.
- Default Log Severity
- Critical
- Parameters
-
- Explanation
- All CLI commands could not be listed by the CLI during the initiation phase. This could result in that some commands are unavailable.
- Gateway Action
- None
- Action Description
- None
- Proposed Action
- Verify that the disk media is intact and functions correctly.
2.5.3. [ID: 213] Failed allocating memory when starting CLI[...]
- Log Categories
- CLI,SYSTEM
- Log Message
- Failed allocating memory when starting CLI command.
- Default Log Severity
- Alert
- Parameters
-
- Explanation
- The CLI failed to allocate the amount of memory needed to start the command.
- Gateway Action
- None
- Action Description
- None
- Proposed Action
- Verify that the system has a sufficient amount of free memory.
2.5.4. [ID: 1118] Attempt to access service command view
- Log Categories
- CLI,SYSTEM
- Log Message
- Attempt to access service command view.
- Default Log Severity
- Information
- Parameters
- user, userid, count, max
- Explanation
- User tried to access to "service" command view.
- Gateway Action
- Deny
- Action Description
- None
- Proposed Action
- None
2.5.5. [ID: 1101] Service command view access granted
- Log Categories
- CLI,SYSTEM
- Log Message
- Service command view access granted.
- Default Log Severity
- Information
- Parameters
- user, userid
- Explanation
- Access to "service" command view was granted to user.
- Gateway Action
- Allow
- Action Description
- None
- Proposed Action
- None
2.5.6. [ID: 1117] Maximum number of service command view access[...]
- Log Categories
- CLI,SYSTEM
- Log Message
- Maximum number of service command view access attempts reached.
- Default Log Severity
- Information
- Parameters
- user, userid
- Explanation
- Maximum number of "service" command view access attempts was reached. Access to "service" command view was rejected and new
challenge is generated.
- Gateway Action
- Deny
- Action Description
- None
- Proposed Action
- None
2.5.7. [ID: 765] Serial console CLI instance started
- Log Categories
- CLI
- Log Message
- Serial console CLI instance started.
- Default Log Severity
- Notice
- Parameters
- user, accesslevel, profile
- Explanation
- A serial console CLI session was started.
- Gateway Action
- None
- Action Description
- None
- Proposed Action
- None
2.5.8. [ID: 769] Serial console CLI authentication failed
- Log Categories
- CLI
- Log Message
- Serial console CLI authentication failed.
- Default Log Severity
- Notice
- Parameters
- user, profile
- Explanation
- A serial console login attempt failed since the supplied username and password could not be verified towards the correct authentication
group.
- Gateway Action
- None
- Action Description
- None
- Proposed Action
- Verify that the user exists with the specified password. Make sure that the user has the appropriate access group(s) (Administrators
and/or Auditor) set.
2.5.9. [ID: 767] Serial console CLI authentication succeeded
- Log Categories
- CLI
- Log Message
- Serial console CLI authentication succeeded.
- Default Log Severity
- Notice
- Parameters
- user, profile
- Explanation
- A serial console login authentication succeeded towards the authentication profile.
- Gateway Action
- None
- Action Description
- None
- Proposed Action
- None
2.5.10. [ID: 773] Serial console CLI session ended
- Log Categories
- CLI
- Log Message
- Serial console CLI session ended.
- Default Log Severity
- Notice
- Parameters
- user, profile
- Explanation
- None
- Gateway Action
- None
- Action Description
- None
- Proposed Action
- None
2.5.11. [ID: 764] Serial console CLI system error
- Log Categories
- CLI,SYSTEM
- Log Message
- Serial console CLI system error.
- Default Log Severity
- Alert
- Parameters
-
- Explanation
- The configuration and authentication of the serial console access is not available. As a result, and for debugging purposes
the serial console CLI is started with administrator privileges.
- Gateway Action
- None
- Action Description
- None
- Proposed Action
- Verify the serial console configuration and restart the system.
2.5.12. [ID: 332] Resource Manager failed memory allocation[...]
- Log Categories
- CLI,SYSTEM
- Log Message
- Resource Manager failed memory allocation when adding data resources.
- Default Log Severity
- Alert
- Parameters
-
- Explanation
- Additional memory could not be allocated when adding data resources.
- Gateway Action
- None
- Action Description
- None
- Proposed Action
- Verify that the system has a sufficient amount of free memory available.
2.5.13. [ID: 483] Resource Manager failed to read information[...]
- Log Categories
- CLI
- Log Message
- Resource Manager failed to read information from resource files.
- Default Log Severity
- Critical
- Parameters
-
- Explanation
- The management system data resources could not be fully updated. This could result in that management systems such as the
CLI no longer functions correctly.
- Gateway Action
- None
- Action Description
- None
- Proposed Action
- Verify that the system has sufficient amount of resources, e.g. free memory. Verify that the storage media is intact.
cOS Stream 4.00.03 Log Reference Guide
